DIY Indilinx SSD with SLC FLASH in HK

admin

Cost:
Indilinx PCB kit = CNY280 + CNY30(sf-express) =~ HKD361
Samsung K9NCG08U5M SLC FLASH 16 pieces = CNY2100 =~ HKD2446

The internal component used is totally the same as OCZ 120GB Vertex EX Series
Jumbo-computer Price at 2010-02-06
[SSD] OCZ 120GB Vertex EX Series 2.5" SATA II SLC Flash SSD OCZSSD2-1VTXEX120G HK$ 9,599.00

This DIY SLC SSD is 1/4 price only! Attactive!

It's an easy soldering job if u know the main point. 1 hour finished.
1. position the SLC FLASH IC as accuate as you can and solder few edge pin
2. apply gel-flux
3. using the hot air gun(HKD190) at ~150c to preheat the soldering area
4. use temperature control soldering iron at ~550f and drag soldering
5. 1 hour finished and earn HKD9599-HKD2446 = HKD7153

charlesl

Could you mind to tell me where i can buy the "Samsung K9NCG08U5M SLC FLASH"?? Thanks

Charles

admin

Could you mind to tell me where i can buy the "Samsung K9NCG08U5M SLC FLASH"?? Thanks

Charles
charlesl 發表於 2010-3-6 12:35 AM

本帖隱藏的內容需要回復才可以瀏覽

rhino

I'm interested too

eXiteRIC

好有興趣喎,效能同原版ocz 有無差別? 另版主可否幫忙焊2件 60g 的? 費用當然我黎俾啦 -0-

admin

好有興趣喎,效能同原版ocz 有無差別? 另版主可否幫忙焊2件 60g 的? 費用當然我黎俾啦 -0-
eXiteRIC 發表於 2010-7-19 07:44 PM

很簡單的, 試試自己焊日日都用著會很有成功感呢,
比ocz還更快(因為ocz賣的還是舊版PCB, 其實已經INDILINX官方證實有潛在干擾問題)
還有買套料時要少心質量, 一樓圖中的PCB是第1版大陸制套料做了幾隻也是用不到幾星期就死忙夠恐怖!
現在已全部改由台灣制而且是2010年新版PCB(INDLINX官方樣本也是用這間廠, 超穩定而且比之前PCB在同一FIRMWARE下還快些)
而價錢也不是相差太多.

eXiteRIC

6# admin

-.- 師兄, d 針腳咁細粒...上高計埋起馬都200幾300條.. 出錯率極高喎.我怕未有成功感失敗感帶黎既沖擊仲大鑊喎. hahaaa..

admin

6# admin  

-.- 師兄, d 針腳咁細粒...上高計埋起馬都200幾300條.. 出錯率極高喎.我怕未有成功感失敗感帶黎既沖擊仲大鑊喎. hahaaa..
eXiteRIC 發表於 2010-7-24 01:34 AM

未試過會以為很高難度, 其實很簡單,
手上的project做完拍條片大家睇睇

完成後可以再用軟件測出假焊,
只要再加錫焊多一次有問題的一針腳就是了.